Αντιστρεπτικές Μπάρες

Χαρακτηριστικά: • Διάμετρος Front: 23mm • Ρύθμιση: Front: No and Rear: No Ταιριάζει σε: Opel Corsa C, Typ Corsa C (not for GSI) - Year: 09/00> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:30mm and Rear:26mm • Ρύθμιση: Front: 2X and Ταιριάζει σε: • Mercedes A-Class + B-Class, Typ 176/ 246/ 245G, 2WD - Year 2012> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:30mm and Rear:26mm • Ρύθμιση: Front: 2X and Ταιριάζει σε: • Mercedes CLA incl. Shooting Brake, Typ 117/ 245G, 2WD - Year 2013> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:30mm and Rear:26mm • Ρύθμιση: Front: 2X and Ταιριάζει σε: • Mercedes GLA, Typ X156 / 245G, 2WD - Year 2013> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Mercedes SLK R170 Χαρακτηριστικά: • Διάμετρος εμπρό : 30mm • Ρύθμιση: Οχι • Μόνο για οχήματα με πίσω αντιστρεπτική μπάρα ! • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Toledo , Typ 1L - Year 1991> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Corrado, Typ 53i, except VR6 - Year 11/88> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Golf II, Typ 19E - Year 08/83> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Golf III Sedan Cabrio/Convertible, Typ 1HXO, 1H, 1EXO, 1E,only 4-hole-wheelwithout GTI-TDI (110 PS), GTI, 16V+VR6/incl. TDI - Year 1991> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Jetta II, Typ 19E - Year 08/83> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Vento Sedan, Typ 1HXO, 1H,only 4-hole-wheelwithout GTI-TDI (110 PS), GTI, 16V+VR6/incl. TDI - Year 1991> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • Audi A3 , Typ 8L, 2WD - Year 08/96> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • Seat Leon , Typ 1M, 2WD except Cupra R - Year 1999> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • Seat Toledo , Typ 1M, 2WD except Cupra R - Year 1999> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • Skoda Octavia Lim+ Sedan/SW , Typ 1U, 2WD except RS Modelle/version - Year 01/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • VW Beetle, Typ 9C, 1Y, 1C, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • VW Bora Lim.+Sedan+SW, Typ 1J, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • VW Golf IV Sedan SW, Typ 1J, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Ibiza incl. Cupra + FR, Typ 6Y, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • Seat Ibiza, Typ 6J, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • Skoda Fabia incl. SW, incl. RS , Typ 6Y, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • Skoda Fabia incl. SW, incl. RS , Typ 5J, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • VW Fox , Typ 5Z, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Polo incl. GTI , Typ 9N, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Ibiza incl. Cupra + FR , Typ 6Y, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Ibiza , Typ 6J, 29015-1 + 29015-2 /Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Skoda Fabia incl. SW, incl. RS , Typ 6Y, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Skoda Fabia incl. SW, incl. RS , Typ 5J, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Fox, Typ 5Z, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Polo incl. GTI, Typ 9N, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over , for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Διάμετρος: Μπροστά 27mm και Πίσω: 23mm • Ρύθμιση: Μπροστά οχ και Πίσω οχι. Σειρά 1 (E82) M-Coupe Σειρά 3 - M3 (E90+92+93)

Κατασκευαστής :: H&R Διάμετρος εμπρός : 30mm Διάμετρος πίσω : 25mm Ρυθμιζόμενο εμπρός: 3 κατευθύνσεων Ρυθμιζόμενο πίσω: 2 κατευθύνσεων

Πάχος : Μπροστά 24mm / Πίσω : 22mm Ρυθμίσεις : Μπροστά 2x / Πίσω 2x Ταιριάζει σε: • AUDI TT + TTS (8J) Quattro - (2007 έως 2014)

Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Audi A3 + A3 Sportback, Typ 8V, 2WD, only for cars with twist beam RA - Year 13> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Seat Leon incl. SC + FR, Typ 5F, 2WD, only for cars with twist beam RA - Year 13> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Seat Leon ST, Typ 5F, 2WD, only for cars with twist beam RA - Year 11/12> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Skoda Octavia Lim+ Sedan/SW, incl. RS, Typ 5E, 2WD, only for cars with twist beam RA - Year 13> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Golf VII Sedan + Variant/SW + Sportsvan, Typ AU/AUV, 2WD, only for cars with twist beam RA - Year 11/12> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:27mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X Ταιριάζει σε: • Audi A3 + A3 Sportback Quattro A3 Sedan, Typ 8V, 4WD,only for cars with multilink RA Sedan + Cabrio/ Convertible: i.V. - Year 13> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:27mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X Ταιριάζει σε: • Audi S3 incl. Sedan + Sportback incl. Cabrio/ Convert., Typ 8V, 4WD,only for cars with multilink RA - Year 13> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:27mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Audi S3 Cabrio/ Convertible, Typ 8V + 8VA, 4WD - Year 13> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:27mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: No and Ταιριάζει σε: • Audi TT Coupe + Roadster Quattro, Typ 8J/8S, 4WD,only for cars with multilink RA - Year 2014> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:27mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: No and Ταιριάζει σε: • Seat Leon X-Perience, Typ 5F, 4WD,only for cars with multilink RA - Year 2014> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:27mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Skoda Octavia Lim+ Sedan/SW, Typ 5E, 4WD - Year 2014> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:27mm and Rear:25mm • Ρύθμιση: Front: 2X and Front: 2X Ταιριάζει σε: • VW Golf VII R incl. Variant/SW R, Typ AU, 4WD - Year 2013> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Audi A3+A3 Sportback incl. Cabrio/ Convertible , Typ 8P, 8PB, 2WD - Year 05/03> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Audi TT Coupe+Cabrio Coupe+Convertible , Typ 8J, 2WD - Year 08/06> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Seat Altea incl. XL , Typ 5P, 5PN, 2WD - Year 05/04> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Seat Leon , Typ 1P, 1PN, 2WD - Year 05/04> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Seat Toledo , Typ 5P, 2WD - Year 05/04> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Skoda Octavia Lim+ Sedan/SW, incl. RS , Typ 1Z, 2WD - Year 04/04> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • Skoda Superb Sedan, Typ 3T, 2WD - Year 07/08> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Beetle, Typ 16,only 2.0L Turbo - Year 09/11> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW EOS, Typ 1F, 2WD - Year 10/03> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Golf V Sedan+ GTI+Golf Plus, Typ 1K, 1KP, 2WD - Year 10/03> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Jetta V Sedan, Typ 1KM, 2WD - Year 10/03> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Passat Sedan+ SW+CC, Typ 3C,3CC, 3c, 2WD - Year 03/05> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Touran+Cross Touran, Typ 1T, 2WD - Year 03/05> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Αντιστρεπτικές μπάρες EIBACH VW CORRADO / GOLF 2 & 3 - (EIB-013-E8502320) Κατασκευαστής: Eibach Κωδικός προϊόντος: E8502-320 EAN: 4050278016919 Διάμετρος Εμπρ. άξονα: 22mm Εμπρ. ρύθμιση: Δεν είναι ρυθμιζόμενη Διάμετρος πίσω άξοναr: 25mm Πίσω ρύθμιση: Δεν είναι ρυθμιζόμενη Ταιριάζει σε: • VW Corrado (53I), • VW Golf II (19E, 1G1), • VW Golf III (1H1), • VW Golf III Cabriolet (1E7), • VW Golf IV Cabriolet (1E7), • VW Jetta II (19E, 1G2, 165), • VW Vento (1H2)

Χαρακτηριστικά: • Διάμετρος Front: 22mm and Rear: 25mm • Ρύθμιση: Front: No and Rear: No Ταιριάζει σε: VW Polo, Typ 9N - Year: 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος Front: 22mm and Rear: 25mm • Ρύθμιση: Front: No and Rear: No Ταιριάζει σε: VW Polo , Typ 9N 29325-1/Set incl. 2 sway-bar-links for coil-over 29325-1 - Year: 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Golf VI incl. Plus, Typ 1K - Year 10/08> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Golf VI Variant /SW, Typ 1KM - Year 09/09> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Golf VI Cabrio/ convertible, Typ 1K - Year 06/11> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: 2X and Front: 2X and Ταιριάζει σε: • VW Scirocco III, Typ 13 - Year 08/08> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος Front: 22mm and Rear: 25mm • Ρύθμιση: Front: No and Rear: No Ταιριάζει σε: VW Golf III Variant/SW, Typ 1HX0, 1H without approval - Year: 93> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση