Volkswagen

Ρυθμιζόμενη 3 σημείων μπροστά αντιστρεπτική της Whiteline 24mm GROUP VAG 4X4 Ταιριάζει σε: AUDI A3 MK 2 (TYP 8P)(7/2004-2012) AUDI Q3 8U (TYP 8U)(6/2011-) AUDI S3 MK 2 (TYP 8P) INCL RS3(7/2004-2012) SKODA SUPERB B6 (TYP 3T)(2008-ON) VOLKSWAGEN GOLF R32 MK 5 (TYP 1K & 1KP) AWD(8/2003-2009) VOLKSWAGEN GOLF R MK 6 (TYP 5K) AWD(2/2009-12/2015) VOLKSWAGEN TIGUAN MK 1 (TYP 5N) AWD(5/2008-) • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Με TUV έγκριση Aποστολή σε όλη την Ελλάδα.

Χαρακτηριστικά: • Διάμετρος Front: 26mm and Rear: 30mm • Ρύθμιση: Front: 2X and Rear: No Ταιριάζει σε: VW Bus T5 incl. Facelift, Typ 7HM, 7HMA, 7HC, 7HCA, 7HKX0, 7HK, 7J0, 2WD+4WD not for Xenon - Year: 03/03> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος Front: 26mm and Rear: 30mm • Ρύθμιση: Front: 2X and Rear: No Ταιριάζει σε: VW Bus T5 incl. Facelift, Typ 7HM, 7HMA, 7HC, 7HCA, 7HKX0, 7HK, 7J0, 2WD+4WD only for Xenon - Year: 03/03> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

WHITELINE πίσω ρυθμιζόμενη αντιστρεπτική 24mm Heavy Duty AUDI A1 MK1 TYP 8X SEAT IBIZA MK4 6J SKODA FABIA MK3 NJ VOLKSWAGEN POLO 6R 6C AUDI A1 2010-2018 - A1 MK1 (TYP 8X) SEAT IBIZA 2008-2017 - IBIZA MK4 (TYP 6J) SKODA FABIA 2014-ON - FABIA MK3 (TYP NJ) VOLKSWAGEN POLO 2009-2017 - POLO MK5 (TYP 6R AND 6C) • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:21mm • Ρύθμιση: Front: No Ταιριάζει σε: Seat Arosa , Typ 6H, 6HS - Year 06/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:21mm • Ρύθμιση: Front: No Ταιριάζει σε: Seat Ibiza/Cordoba incl. Vario , Typ 6K except Cupra+Cordoba 6K/C - Year 1993> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:21mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Lupo, incl. GTI, Typ 6X, 6ES, FSI+3L Lupo, incl. Classic+Variant/SW - Year 09/98> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:21mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Polo, Typ 6N, 6KV, incl. Classic+Variant/SW - Year 09/94> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Seat Ibiza/ Cordoba incl. Cupra + FR , Typ 6L, 1P, 2WD, Set incl. 2 sway-bar-links for coil-over 29325-1 - Year 03/02> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Skoda Fabia incl. Kombi incl. SW, incl. RS , Typ 6Y, Set incl. 2 sway-bar links for coil-over kit 29325-1 - Year 01/00> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Skoda Fabia incl. Kombi incl. SW, incl. RS , Typ 5J, Set incl. 2 sway-bar links for coil-over kit - Year 03/07> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Fox, Typ 5Z, 29325-1/Set incl. 2 sway-bar-links for coil-over 29325-1 - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Polo incl. GTI, Typ 9N 29325-1/Set incl. 2 sway-bar-links for coil-over 29325-1 - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Audi A1 incl. Sportback, Typ 8X, 2WD - Year 08/10> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Seat Ibiza/ Cordoba incl. Cupra + FR , Typ 6L, 2WD - Year 03/02> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Skoda Fabia incl. SW, incl. RS , Typ 6Y - Year 01/00> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Skoda Fabia incl. SW, incl. RS , Typ 5J - Year 03/07> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Fox, Typ 5Z - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Polo incl. GTI, Typ 9N - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • Audi A1 incl. Sportback, Typ 8X, 2WD - Year 08/10> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Ibiza FR , Typ 6J, 2WD - Year 06/08> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. Cut out front inner plastic wheel house for sufficient freedom of motion 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Polo , Typ 6R, 2WD except GTI + WRC - Year 08/10> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος Front: 22mm and Rear: 25mm • Ρύθμιση: Front: No and Rear: No Ταιριάζει σε: VW Polo , Typ 9N 29325-1/Set incl. 2 sway-bar-links for coil-over 29325-1 - Year: 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος Front: 22mm and Rear: 25mm • Ρύθμιση: Front: No and Rear: No Ταιριάζει σε: VW Polo, Typ 9N - Year: 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Ibiza incl. Cupra + FR , Typ 6Y, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Ibiza , Typ 6J, 29015-1 + 29015-2 /Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Skoda Fabia incl. SW, incl. RS , Typ 6Y, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Skoda Fabia incl. SW, incl. RS , Typ 5J, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Fox, Typ 5Z, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Polo incl. GTI, Typ 9N, 29325-1 + 29325-2/Set incl. 2 sway-bar-links for coil-over , for cars with a big square-cut muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Ibiza incl. Cupra + FR, Typ 6Y, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • Seat Ibiza, Typ 6J, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • Skoda Fabia incl. SW, incl. RS , Typ 6Y, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • Skoda Fabia incl. SW, incl. RS , Typ 5J, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No Ταιριάζει σε: • VW Fox , Typ 5Z, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Polo incl. GTI , Typ 9N, for cars with a big square muffler. - Year 11/01> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. This stabilizer set - including two sway bar links - is for use with coil-over 29 325-1 only and must be used for lowering beyond approx. 50 mm to achieve sufficient freedom of motion between driveshaft and stabilizer. 3. Cut out front inner plastic wheel house for sufficient freedom of motion ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

• Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Εμπρ. Πάχος: 25mm • Πίσω Πάχος: 21mm • Εμπρ Ρύθμιση: 2x • Πίσω Ρύθμιση: 2x • Εμπρ. Κωδ.: 33431 VA • Πίσω Κωδ.: 33431 HA Ταιριάζει σε: • Audi S3 Quattro 1999>, Typ 8L, 4WD S Σημείωση: 1. When fitting H&R stabilizers use OE mounting parts if not co-packed. Check that these parts are in a like-new condition; renew them in case they are not. 2. Height adjustableat the front axle only

Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • Audi A3 , Typ 8L, 2WD - Year 08/96> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • Seat Leon , Typ 1M, 2WD except Cupra R - Year 1999> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • Seat Toledo , Typ 1M, 2WD except Cupra R - Year 1999> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • Skoda Octavia Lim+ Sedan/SW , Typ 1U, 2WD except RS Modelle/version - Year 01/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • VW Beetle, Typ 9C, 1Y, 1C, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • VW Bora Lim.+Sedan+SW, Typ 1J, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:26mm and Rear:22mm • Ρύθμιση: Front: No and Front: 2X and Ταιριάζει σε: • VW Golf IV Sedan SW, Typ 1J, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Audi A3 , Typ 8L, 2WD - Year 08/96> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Seat Leon , Typ 1M, 2WD except Cupra R - Year 1999> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Seat Toledo , Typ 1M, 2WD except Cupra R - Year 1999> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: Skoda Octavia Lim+ Sedan/SW , Typ 1U, 2WD except RS Modelle/version - Year 01/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Beetle+Beetle Cabrio/ Convertible, Typ 9C, 1Y, 1C, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Bora Lim.+Sedan+SW, Typ 1J, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm • Ρύθμιση: Front: No Ταιριάζει σε: VW Golf IV Sedan SW, Typ 1J, 2WD - Year 07/97> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση

• Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Εμπρ. Πάχος: 25mm • Πίσω Πάχος: 28mm • Εμπρ. Κωδ.: 33 865 VA3 (Μη Ρυθμιζόμενη) • Πίσω Κωδ.: 33 865 HA2 (3 Σκάλες Ρύμισης)

• Μειώνει τις στρεβλώσεις του σασί. • Βελτιώνει το κράτημα του αυτοκινήτου. • Μειώνει την υποστροφή και την υπερστροφή. • Διατηρείται η εργοστασιακή άνεση. • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών. • Με TUV έγκριση. Χαρακτηριστικά: • Διάμετρος Μπροστά: 25mm • Διάμετρος Πίσω: 25mm • Ρύθμιση: Οχι

Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • Seat Toledo , Typ 1L - Year 1991> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Corrado, Typ 53i, except VR6 - Year 11/88> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Golf II, Typ 19E - Year 08/83> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Golf III Sedan Cabrio/Convertible, Typ 1HXO, 1H, 1EXO, 1E,only 4-hole-wheelwithout GTI-TDI (110 PS), GTI, 16V+VR6/incl. TDI - Year 1991> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Jetta II, Typ 19E - Year 08/83> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Χαρακτηριστικά: • Διάμετρος: Front:22mm and Rear:25mm • Ρύθμιση: Front: No and Front: No and Ταιριάζει σε: • VW Vento Sedan, Typ 1HXO, 1H,only 4-hole-wheelwithout GTI-TDI (110 PS), GTI, 16V+VR6/incl. TDI - Year 1991> Σημείωση: 1. Front axle - Only if the distance of the bottom fastening point bracket (center of the hole) up to the centre line of the strut housing = 56 mm AND: If the distance of both fastening holes in the bracket = 54 mm ( center of the hole). Take these dimensions carefully from the original strut! 2. When fitting rear axle stabilizers together with non OE exhaust systems packaging problems might arise. A contact between stabilizer and exhaust is possible. This has to be checked prior to fitment and solved prior to first driving. 3. FA stabilizer may also be used without rear stabilizer. In this case vehicle might tend to understeer. ------------------------------ Επιπλέον πληροφορίες: • Μειώνει τις στρεβλώσεις του σασί • Βελτιώνει το κράτημα του αυτοκινήτου • Μειώνει την υποστροφή και την υπερστροφή • Διατηρείται η εργοστασιακή άνεση • Συμβατό με την εργοστασιακή ανάρτηση ή sport αναρτήσεις άλλων εταιριών • Σχεδιασμένο, κατασκευασμένο και ελεγμένο στην Γερμανία • Με TUV έγκριση